For a miniature radial ball bearing listed as d × D × B, read the dimensions as bore diameter, outside diameter and axial width, in that order. Keep the units with all three numbers. Matching only the hole, only the outside diameter or a photograph is not enough to order a fishing reel bearing.
Those dimensions help identify a part; they do not authorize a substitute. Confirm the exact reel, bearing position and complete approved specification before purchase. This guide explains size information and a careful recording workflow, not reel disassembly, a fault diagnosis or a universal bearing upgrade.
Jump to the three dimensions, a documented example, sizing traps, the recording workflow or FAQs.
Three dimensions describe three different interfaces
d: the bore, or inside diameter
Lower-case d describes the bore through the inner ring. It is not the diameter of a ball, a screw head or the complete bearing. In a suitable assembly, this is the dimensional reference associated with the shaft interface.
A bearing that appears to slide over a shaft has not passed a complete fit check. Nominal dimensions, the specified mounting fit and the condition of the mating parts are separate considerations. Do not sand the shaft or force a trial part into place.
D: the outside diameter
Upper-case D describes the outside diameter of the bearing's outer ring. It is different from d even though the same letter is used. Preserve the case when copying a manufacturer's table.
Do not substitute the outside of a surrounding holder, removable sleeve or decorative cap for the bearing's own outer diameter. If you cannot identify the component boundaries, use the approved parts information or qualified assistance rather than measuring the whole assembly and calling it one bearing.
B: the axial width
B is the width identified in the applicable product drawing, measured along the bearing axis rather than across its circular face. Width matters independently of both diameters.
A correct-looking front view can conceal a width mismatch. An adjacent washer, spacer or retaining component is not automatically part of that width. Preserve the complete assembly information instead of deleting a spacer to accommodate a thicker substitute.

A documented 5 × 11 × 4 mm example
NSK's MR115ZZ product table lists d = 5 mm, D = 11 mm and B = 4 mm. Read together, those entries describe a 5 × 11 × 4 mm dimensional envelope.
Reversing the first two numbers changes the meaning. Omitting the final number drops the width. Writing only “11 mm bearing” leaves it unclear which dimension you mean.
This is a manufacturer's published example of dimension notation, not a claim that MR115ZZ is installed in a GOOFISH reel or is an approved fishing-reel replacement. Do not use the example to fill a missing specification in your own parts request.
Two traps that a three-number listing can hide
A flange adds dimensions beyond d, D and B
A flanged bearing has an additional projecting feature that must be accounted for using the relevant drawing. The broadest visible diameter is not necessarily the dimension labeled D.
For example, NSK's F601X table lists D = 6 mm separately from a 7.5 mm flange diameter, as well as a flange-width entry. That distinction demonstrates why measuring across a flange and recording it as ordinary outside diameter can misidentify a part.
Do not transfer this example's dimensions or flange notation to another bearing. Preserve the actual drawing and ask which surfaces each dimension refers to. Removing a flange or substituting an unflanged bearing is not a sizing correction.
A millimeter display does not prove a metric-series bearing
An inch-series bearing can also be described with millimeter dimensions. NSK's FR2 inch-series table, for instance, gives d = 3.175 mm, D = 9.525 mm and B = 3.967 mm, with separate flange information.
Do not round a small measurement to the nearest convenient whole-millimeter size and assume the catalogue match is confirmed. Preserve the units, original designation and actual reading. If the observed size and documented size disagree, resolve the discrepancy before ordering.
A practical recording workflow, without a teardown experiment
- Start with the reel and position. Record the full model, generation and retrieve-hand version. Use the correct parts reference to identify which bearing is being discussed.
- Look for approved information first. Request the manufacturer part number, complete bearing designation and relevant drawing. Existing service documentation can be more useful than a new measurement.
- Measure only an appropriately accessible, identified part. If a qualified service process has already made the bearing available, use suitable measuring equipment and its instructions. Do not open the reel solely to complete this checklist.
- Record d, D and B separately with units. Keep instrument readings distinct from nominal catalogue dimensions. Note any flange, sleeve, spacer or uncertainty rather than combining it into an unexplained number.
- Check the complete specification. Ask for confirmation of the part's construction, closures, material, clearance, tolerance and lubrication as applicable to the exact position, not just its three dimensions.
- Resolve differences before purchase or installation. Do not use pressing force, altered hardware or extra shims to make an unconfirmed part fit.
With small bores and narrow faces, access and tool positioning can make readings difficult. A caliper display is identification evidence, not a tolerance certificate. If a reading changes with tool position or cannot be taken confidently, record that limitation and obtain appropriate measurement support. More decimal places do not, by themselves, prove greater accuracy.
Keep a compact record: reel identity, bearing position, approved part reference, d, D, B, units, any flange information, measurement source and unresolved questions. Leave an unknown field unknown rather than borrowing a number from another reel.

A reel's bearing count is not its bearing size
The GOOFISH BCS250 saltwater baitcasting reel lists 10+1 stainless steel bearings, 6.18:1 gearing, and separate left- and right-hand retrieve versions in Silver and Gold. Those details identify the model and its listed configuration. They do not provide the dimensions of each internal bearing.
Do not interpret 10+1 as d, D or B, assume every bearing inside has one size, or infer cross-model compatibility from a similar gearing figure. Include the actual retrieve version and bearing location in a service enquiry. The dimensional examples above are not a BCS250 replacement chart.
Likewise, selecting a new bearing does not establish a higher maximum drag, a waterproof reel or a different rod load allowance. Match the complete fishing outfit separately; an unexplained roughness should be assessed before treating a replacement bearing as the solution.
Keep size, part identity and bearing grade separate
Three correct dimensions are necessary identification details, but they do not describe every feature of a bearing or its role in an assembly. An equal-size item with a different specified construction is not automatically an approved substitute.
The reel schematic and replacement-part guide covers the document-to-part identity trail. For the separate meaning of precision and clearance labels, read ABEC grade versus internal clearance. Neither question can be answered from bore diameter alone.
Fishing reel bearing-size FAQs
What order are the numbers in a d × D × B listing?
Bore diameter, outside diameter and axial width. Confirm the units and the actual manufacturer's notation.
Can I order from a photograph next to a ruler?
Use it as supporting context, not a verified dimensional or compatibility specification. Perspective and the visible assembly boundaries can leave important details unresolved.
Does a matching bore mean the bearing fits?
No. Outside diameter, width, any additional features and the complete approved specification still need confirmation.
Should I remove shields to measure width?
Do not dismantle closures just to obtain a size. Use the documented drawing and suitable qualified measurement support where needed.
Can a matching-size bearing be an upgrade?
Dimensions alone do not establish an improvement or authorize a substitute. Obtain approval for the precise part and position rather than choosing by size or free-spin claims.
Read all three dimensions, retain the units and confirm the complete part. That is a more reliable ordering method than turning one plausible diameter into a confident replacement choice.