Skip to content
Goofish® Rod-More than fishing
0 items in cart

Cart

Your cart is empty.

Tips for trolling reels

Trolling Lines Tangle on Turns? Check the Spread Before the Reel

· Goofish®Rod-More Than Fishing

Curved boat wake with inset conventional reel and closed tackle case photographs, headed Tangles on the Turn

The trolling spread runs cleanly on a straight course. The boat turns, one rod unloads, another changes rhythm, and two lines converge. Before blaming the reels, ask what the turn changed beneath and behind the boat.

A turn changes the routes of the lures and their relationship to one another. Inside and outside presentations may experience different motion and loading. Line bow, lure design, current and deployment length complicate the result. A clean straight-line spread is not proof that it will remain clear through every course change.

This guide focuses on conventional trolling outfits and crew coordination. Specialist planer-board, downrigger and diver systems need their own operating procedures. Navigation and vessel control remain the skipper's responsibility.

Why the outside and inside presentations differ

During a turn, outside and inside positions follow different paths. In a simplified arrangement, the outside path is longer and the inside path shorter. That helps explain why lure behavior can change even when the boat's displayed speed seems steady.

Real lures do not behave like rigid points attached to the boat. They trail behind on flexible line, respond to water flow and may follow delayed or changing paths. Do not convert a turn angle into an exact lure speed or assume each lure stays directly behind its rod tip.

Current matters too. Speed over ground describes boat movement relative to the earth, not each lure's speed through the surrounding water. Turning across or into a flow can change the presentation without an obvious change in that displayed number.

Do inside lures sink and outside lures rise?

That is not a universal rule. A slowing weighted or sinking presentation may descend, but a buoyant diving plug can respond differently as water flow changes. A lure can also lose its intended action or become unstable outside its suitable operating range.

Depth depends on the complete system: lure design, weighting, line type and length, current and motion. A change in rod bend cannot tell you the exact lure depth or prove that a fish has struck.

Use the lure and deployment system's guidance. Do not apply one fixed turning-speed correction to every rig, and do not add weight simply because a tangle happened on the inside of the turn.

1. Establish the straight-course baseline

Before diagnosing turns, confirm that the spread is controllable while running normally. Watch each rod's usual loading and rhythm, the visible line directions and any signs that a lure is fouled or running poorly.

Record which lure is deployed from each position and its relevant deployment reference. A counter or marked line can aid repeatability, but line released is not a direct measurement of lure depth or horizontal distance behind the boat.

Check the actual holders, retention arrangements, line routes, knots and reel operation. More rods are not automatically a better spread. If the crew cannot monitor and manage the arrangement, simplify it before adding complexity.

2. Agree on the turn before it happens

The skipper should know what is deployed and whether the crew can manage the planned course change. Agree who watches each outfit and what to report. A short warning before a turn gives people time to observe rather than react after lines cross.

Where navigation and conditions permit, the skipper may choose a broader course change or have selected lines recovered first. There is no universally safe turning radius or line-spacing formula for every vessel and spread.

Do not tell the skipper to hold an unsafe course to protect the tackle. If a maneuver is required for vessel safety, follow instructions and report the line situation clearly.

3. Watch for changes, not just an alarm

Look for an unusual convergence of visible lines, a rod suddenly unloading, abnormal vibration or a load unlike the straight-course baseline. These are reasons to assess the setup, not proof of a particular underwater event.

A clicker, where fitted, can draw attention to movement. It cannot distinguish a fish from changing presentation load or a snag. Our clicker-versus-drag guide explains why an alert and a working drag setting are separate functions.

Avoid feeding out line automatically when a rod unloads. That can add uncontrolled slack without resolving the changing lure paths. Likewise, tightening drag to silence an alert does not separate crossed lines.

Seafoam and rose triptych showing a curved wake, stationary conventional reel and notebook, labelled Lure Path, Line Behavior and Crew Response
A course change deserves a fresh check of lure behavior, line relationships and the crew's response plan.

4. If lines converge, communicate before changing everything

Report the affected positions and what you see: two lines moving together, one rod losing load or a fixed resistance. Follow the skipper's recovery plan rather than having several anglers independently alter line length and reel controls.

Do not move a loaded rod across other anglers or reach over moving line. Keep hands away from loaded braid, hooks and reel mechanisms. Never wrap line around a hand to separate a crossing.

Recover the affected equipment only in the controlled sequence appropriate to the vessel and spread. A suspected snag requires its own response; do not use the reel handle or a heavily bent rod to force it free. Any necessary boat-speed or propulsion changes belong to the skipper.

5. Inspect the recovered rig before redeploying

Contain sharp tackle and remove load safely before examining a tangle. Check affected line, leaders, knots, clips and hooks. Look for abrasion, displaced components, weeds or a fouled lure that could have changed its tracking.

Do not pull tight knots apart under uncontrolled tension or cut loaded line. Replace damaged sections and restore the intended rig appropriately. Collect offcuts instead of letting them fall onto the deck or into the water.

After a reset, change one manageable factor at a time where practical. A simplified spread, different deployment arrangement or altered course plan may be more informative than replacing several lures and reels together.

What a trolling reel specification does not solve

The GOOFISH SW series trolling reel listing identifies SW13000 and SW15000 options with a stated 3.3:1 gear ratio. Those are product-selection references, not a guarantee that a multi-line spread will remain clear through turns.

Gear ratio does not set a trolling lure's water speed, and ratio alone does not specify line recovered per handle turn. Check the complete rod, reel, line and deployment method, along with model-specific controls and operating guidance.

Confirm any required clicker, counter or line-management feature rather than inferring it from the trolling-reel label. A larger capacity or maximum-drag figure is not a solution to an unmanageable spread.

A turn-and-spread log

Fishing position and lure at each rod:
Deployment references and their limitations:
Straight-course baseline:
Turn direction and relevant current or wind observations:
First visible change and affected positions:
Crew response and recovered-rig findings:
Single adjustment before the next comparable pass:

Record clean turns as well as tangles. One strike on an outside lure does not prove that a turn pattern is universally better, and one clean pass does not establish a safe arrangement for different conditions.

Before a trip, the first charter tackle checklist helps establish who manages the spread and what equipment the operator supplies.

Trolling turn FAQ

Why do my lines only tangle on corners?

The course change can alter lure routes, loading and line relationships. Compare the spread before and during the turn, then inspect the recovered rigs rather than assuming the reel caused it.

Should I release more line on the inside?

Not automatically. Extra line can create slack or increase interaction with other presentations. Follow the planned deployment and crew procedure.

Does unchanged GPS speed mean unchanged lure action?

No. The display does not measure every lure's motion through water. Current, path and lure response can differ.

Will a swivel prevent crossed trolling lines?

A suitable swivel can serve a particular rig function, but it does not keep separate lines from following intersecting paths.

Is a wide turn always safe?

No. Navigation, other vessels, hazards, conditions and the actual spread still matter. The skipper determines the vessel maneuver.

Treat the turn as a new presentation, not a continuation of the straight run. Watch the spread, communicate early and reset before uncertainty becomes a loaded tangle.


0 comments

Add a comment

Keep reading

More from Tips for trolling reels

View all articles
  • Empty conventional reel spool beside separate braid and monofilament coils illustrating shared capacity planning

    Braid Backing and Mono Topshot: One Spool, Not Two

  • English Cam vs Preset cover with a generic conventional reel introducing how to read a drag-response curve

    Lever-Drag Cams vs Preset: Read the Drag Curve

  • Generic conventional reel with two top-frame harness lugs and an English attachment-verification headline.

    Fishing Reel Harness Lugs: Verify Before You Clip In

Shop this guide

Gear mentioned in this article

  • Blue and gold SW Series trolling reels together on a white background, showing their frames, spools and handles

    Heavy Duty Trolling Reel: 3.3:1 Gear Ratio | 2+4 BB | Forged Aluminum Spool for Deep Sea Fishing

    Price range: $128.00 USD – $138.00 USD

Field notes

Get new fishing guides in your inbox

Practical rod, reel and technique guides from the GOOFISH® blog. Unsubscribe anytime.