GOOFISH EBINOD 2402MH Hitotsu Tenya Spinning Rod | 240cm

EBINOD 2402MH: a focused hitotsu-tenya spinning setup

Image coverage remains incomplete: The three accepted detail renders below show the triggerless grip direction, composite-joint/fine-tip direction and English marking/cap direction. Full-rod and separate-section attempts were rejected for structural, proportion or guide-count errors and are not included. An accurate complete-rod and two-section image set is still required before release. The macros do not establish exact installed FUJI geometry, original-vector logo fidelity or manufacturing dimensions.

The GOOFISH EBINOD 2402MH is being developed for boat anglers working shrimp-baited hitotsu-tenya rigs for locally appropriate sea bream, including madai. Its 240cm, two-piece spinning direction combines a compact hand-held grip with a fine upper-tip design for controlled lowering, lifts and falls. Mint Violet pairs a mint-green lower blank, violet EVA rear grip, short warm-white EVA foregrip and a small orange butt bumper.

This is one model with one finish. It is not a tachiuo/cutlassfish Tenya rod, a tai rubber casting rod, a squid tip-run rod or a heavy wreck-fishing rod. Use conditions that allow controlled bottom contact, a manageable line angle, clear rod movement along the rail and appropriate landing equipment. No universal depth, current speed or fish-weight limit has been established.

Specification status: Every new rating, dimension, material selection, mass, balance and installed-component detail below is a development target pending engineering approval and physical samples. Named FUJI parts are researched candidates, not confirmed installed stock. Images are design renders, not product photographs, exact component drawings or manufacturing instructions. No sensitivity, strength, anti-slip, fatigue, catch-rate or casting-distance result is claimed. USD169 is a suggested price awaiting supplier quotations, not a confirmed cost or margin.

Choose the one dedicated model

Head weight and complete wet-rig weight answer different questions. Weigh the actual assembly rather than relying on the sinker label. The proposed head window does not approve metal jigs, heavy extra sinkers, long-range casting or snag extraction. Power, Action, line class and fish mass cannot be used to calculate safe rod force or reel drag.

A coherent two-section geometry

All values here are development targets. The common datum is the outside butt-cap end, x=0, measured toward the tip along the straight assembled centerline. The finished base assembly S1 is1235mm, including its cap; S2 is1235mm, including the tip-top projection. A70mm composite put-over engagement gives1235 +1235 −70 =2400mm. S2 starts at assembled x1165mm and overlaps the male base to x1235mm.

These are finished assembly envelopes, not raw tube cutting instructions. Raw carbon lengths, cap sockets, tip-top projection, sanding allowance, engagement tolerance, residual joint gap and reinforcement require approved drawings. Keep print, coating and excess adhesive outside the mating lands. Do not force a connection flush or pull on guide frames during separation.

The intended upper is a tubular carbon-composite structure with a permanently bonded solid-carbon tip candidate. An exposed solid-tip length320mm and bonded splice length50mm are development targets only: exposed solid-tip direction x2080–2400mm, internal splice direction x2030–2080mm. This is not an interchangeable spare tip or a third removable section. Tip taper, finished diameter, wall transition, resin, adhesive, overlap and stiffness continuity must be engineered before the sample is built. No carbon brand, modulus, layup or resin system is confirmed.

The1285mm protected-length target allows25mm at each end of the1235mm longest assembly. Radial protection must accommodate the high first guide and a separator; an initial110mm internal sleeve-clearance target requires actual envelope testing. Packed length, raw tube length and assembled length must not be confused. Package dimensions and shipping weight remain unmeasured.

Grip chosen for hand-held boat work

The intended method involves holding the rod through controlled drops, bottom checks and repeated lifts, with wet hands or light gloves. A shaped violet EVA rear grip and short warm-white EVA foregrip are selected as a reproducible compact form and coordinated color route. These are design reasons, not verified anti-slip, thermal, sensitivity or comfort advantages.

Natural cork was considered for its tactile finish and warmth of appearance, but bait staining, grade and filling consistency require trials. Composite cork offers another manufacturable shape, with density, bonds and finish still to test. Carbon-grip options require separate wet, cold and gloved handling assessment; no automatic performance benefit is assumed. EVA must pass the same durability and contamination checks rather than being treated as a default black material.

Installed axial targets: orange bumper x0–12mm; continuous violet EVA rear x12–170mm, length158mm; exposed graphite gap x170–195mm, length25mm; rear trim x195–200mm; seat reserve x200–335mm, length135mm; front trim x335–340mm; warm-white EVA fore x340–365mm, length25mm; winding check x365–370mm. Total handle envelope370mm target. Rear grip outside diameter24–27mm, foregrip23–25mm and bumper27mm are development targets. The exposed gap is an arrangement choice, not a claimed weight or balance improvement.

Candidate FUJI VSSSD16CC has a source-listed13.0mm bore,120mm body length, OD references18.3/14.8/23.0mm and38.5mm sub-dimension. These catalog dimensions are not installed measurements. The body is allocated approximately x207–327mm within the135mm seat reserve; actual hood/nut movement, reel-foot contact and matching shaped grip need supplier approval. A120mm body is not the whole installed stack. Blank diameter, arbors and adhesive gaps cannot be inferred from the13mm bore.

Test the actual reel foot length, width and curvature, locking travel, rotor/bail sweep, handle-knuckle clearance, wet/gloved finger support, spool coil path and loaded center of gravity. Nominal reel size alone does not approve fit. No existing GOOFISH reel is claimed to be fit-validated for EBINOD.

FUJI candidate guide and tip plan

One candidate train contains nine guides plus one tip-top: BCKLAG20H×1 atx700mm; BCKLAG10H×1 atx1080; BCKLAG5.5M×1 atx1400; BCKBAG5.5×1 atx1670; BCKTAG5.5×5 atx1880,2040,2175,2280 and2355; BCLGAT5.5-family tip-top×1 atx2400. All are unvalidated ring-center design stations from the butt datum, not wrap-foot edges or released production locations. Two guides lie on S1 and seven on S2. The plane is below the assembled blank, not above and not spiral-wrapped.

KL, KB and KT are single-foot candidate frames; KB provides the proposed transition-foot arrangement, not an untested strength claim. BC finish is source-listed frosted dark-grey stainless; ring material is Alconite. Catalog guide height/overall-length references in mm:20H50.8/37.5;10H30.2/26.6 in one regional table versus28.6 in other distributor references;5.5M14.6/16.8;KT5.5 7.3/10.6. KB5.5 complete drawing and dimensions remain supplier-pending. The10H discrepancy must be resolved against the actual current part, not averaged or silently combined. Nominal ring numbers are not clear apertures or verified knot clearance.

Candidate top family BCLGAT5.5 is source-listed Alconite in a dark-grey stainless glue-on LG frame. Catalog variants include5.5/1.2 and5.5/1.4; these are not alternate rod variants and no tube is released. For reference, the5.5/1.2 example lists L12mm, H6.5mm and outer tube diameter1.4mm. Measure the finished solid-tip outside diameter, coatings and correct adhesive fit before selecting a tube. Full current ordering suffix, actual quantity availability, frame footprint, wrap lengths and seat contents require supplier confirmation. No invented order number substitutes for an unresolved fit.

The target reel, filled spool, wet leader knot, static routed-line path, tip deflection and suspended-rig trials determine final guide count and positions. Images do not define exact FUJI shapes, stations or production geometry. A changed guide train triggers mass, balance and line-path retesting.

Mint Violet finish and English markings

Mint-green lower coating target x370–1120mm; graphite joint reserve and upper blank; violet continuous rear EVA; warm-white short foregrip; small orange bumper and restrained tip accents. The last250mm white-tip coating direction x2150–2400mm is a development appearance target requiring adhesion, flex and visibility trials. It is not luminous and does not establish better bite detection. Guide wraps are dark graphite/violet with narrow mint trim, subject to approved wrap lands.

PANTONE3255C,7672C and1585C are respectively mint, violet and orange reference targets from the Solid Coated system. Warm-white is a physical neutral master to approve, not an invented matching Pantone code. Separate physical masters are required for blank coatings, metal trim, EVA, thread and ink. Paper color references and screen simulations do not specify foam, paint or anodizing chemistry. Functional threads, hood contacts, mating lands and adhesive zones remain undecorated.

All marking positions below are development targets, referenced from x=0 and the12-o'clock branding face opposite the6-o'clock guide plane. Use the original connected-double-O GOOFISH wordmark without stretching or redrawing. Logo area x400–465mm, nominal65×8mm with original aspect ratio controlling the height; EBINOD2402MH area x400–485mm,85×3.5mm, on a separate angular line to avoid overlap. English target-spec block x500–625mm,125×2.5mm per line at4mm baseline spacing: “240cm TARGET |2PC |MH FAST”; “TENYA HEAD10-55g TARGET”; “TOTAL RIG65g TARGET |NOT A CAST RATING”.

Reverse-side batch field x760–800mm,40×2.5mm, with no fictitious batch number assigned. S1 identification x1100–1112mm, S2 at local90–102mm,12×2mm. Alignment ticks: S1x1145–1153mm and S2local80–88mm,8×0.7mm, outside the70mm mating lands. Restrained violet band x640–641mm. Orange tip accent bands x2365–2367 and2380–2382mm must be reviewed against guide wraps and flex. Butt-face logo target17×3mm on the27mm cap, preserving the original proportions. Keep at least5mm target clearance from wraps, coating steps and interfaces, subject to supplier proof.

The available logo bitmap is a visual reference, not a production vector. Original vector artwork, curved-surface proof and compatible pad-print/transfer trials are required. Coat, ink, thread and light foam need wet bait, sunscreen, salt residue, cleaner, rub-transfer, UV-fade and aging tests. No stain resistance, washability, grip or lifetime claim is established.

Engineering gates, not inferred strength ratings

Keep rod working line load, recommended reel drag, complete line-system tensile strength and destructive rod force separate, measured in newtons under their own documented conditions. No force is calculated from fish weight, PE, MH, head mass or suspended-rig mass. No safe reel-drag value, maximum fish mass or destructive threshold is assigned.

Every test record must specify the sample and lot, calibration, environment, supports and grip/contact positions in mm, rod angle in degrees from horizontal, load point and complete line path, loading speed in N/s or mm/s, hold in seconds, cycles, sample quantity, numerical acceptance and responsible approval. Missing force, speed, time or acceptance limits are engineer-approval gates before testing, not permission to improvise.

From development input to sample approval

Direct development inputs: one hitotsu-tenya spinning model,2400mm controlling length chain, two removable sections, compact EVA grip, restrained Mint Violet palette and original-wordmark requirement. These are design inputs, not measured specifications.

Engineer/supplier decisions: all tolerances, taper, layup, wall transitions, resin/cure, solid-tip and splice geometry, joint fit and gap, finished diameters, arbors and adhesive gaps, guide footprint and stations, reel-foot and hood travel, EVA/ink/coating processes and protective clearance. Resolve them into controlled drawings and a current BOM before building.

Sample-only approvals: Power and Action, operating rig window, working load and drag recommendations, finished mass/balance, static/dynamic line clearance, wet/gloved handling, bonds, cyclic/destructive results and material durability. Inspect, test, log deviations, revise the affected design/process, rebuild and retest before blank engineer, component supplier, quality and product-owner approval. A saved draft or attractive image is not permission to manufacture or sell.